POPPUMP Yugoslavia Technical Center

Tel:(001)3474109611

POPPUMP logo

POPPUMP Yugoslavia Technical Center , Discuss Technical Problem , Suply After Service Online of Fuel Dispenser, Please Regist Firstly

D-GC88 FUEL DISPENSER

D-GC88

D-GC88 FUEL DISPENSER

Pump :Type Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.): 55±5

Suction Distance (m) :6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy :±0.2%

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type :Solenold Vale Control Type

Preset :Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price: 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose :4.5m

Weight :450kg

Dimension(L×W×H): 1615 X 620 X2420(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 26

products links

links

technical archives

    l gear pump Trouble and Maintenance The mainly troubleshooting and failure about pump presents in Table 2-1. Table 2-1 Troubleshooting Serial No. Failure Failure reasons Solutions 1 No delivery or inefficient discharge Exterior elements: Motor stick; fuel dispenser motor reversal; Sliding V belt; no oil in tank; pipe jammed; Check motor and its wiring; tighten V belt; inspect tank; dredge pipeline. Gear being stuck Clean waste in pump chamber Waste in outlet of overflow valve Disconnect overflow valve lid and clean waste; Leakage on valve Check oil groove Overweary gear or bearing Replace gears or bearing 2 Large noise or tremble Exterior reasons: Too long horizontal distance between fuel dispenser and tank; many elbow on inlet pipe; waste jam pipe; small diameter of pipe Dealt with in design and construction Intensive pressure Decrease thickness of pressured ring Overflow valve is stuck Clean waste and burr Overweary gear or bearing Replace gears or bearing 3 Inner leakage Overweary gears Replace gears Leakage on frame seal Frame seal disabled Replace frame seal Leakage on pump body or joint face O-ring disabled Substitute seal ring 2.5 Important notices in operation Often inspect the rotation of pump axis, leakage, abnormal noise, vibration on V wheel and lose bolt that tight pump key. Regularly clean strainer. The tightness of V wheel should be appropriate, neither too tight nor too loose. These V wheels of motor, pump and adjusting driven wheel should be in parallel level. Don’t adjusting overflow valve spring too tights in case that result in high pressure of hydraulic system, increase noise and vibration so as to enhance pump abrasion fuel dispenser . Prohibit suck water or oil with much water. Strictly abide by the operation requirements on explosive atmosphere. Submersible pump In China filing stations recently begin to adopt submersible pump as the power resource of fuel dispenser. Submersible pump gen fuel dispenser

technical specification

    than IPAddress of the POS workstation in the Login message which is renamed   POSAddress.  B.4.3 Protocol State Table  State Table States events table for the processing of frame emission are presented below.〠fuel dispenser €ã€€Frame  Emission  State Comment  Idle No frame emission pending all the sending requests are completed.  Sending An information frame sending is started last byte of the frame is not sent.  Wait Ack An information frame is sent an ACK or a NAK is waiting.  Table B.1: Frame Emission States  State Comment  Send Message Application requests to send a message to a destination address.  Emission End Last information frame byte is just sent.  Emssion Error An error while sending Information frame has occurred.  Receive Ack ACK is receivedby the reception processing  Receive Nak NAK is receivedby the reception processing  Time out Timer has expired  Send Ack Transport protocol want to acknowledge an Information frame.  Send Nak Transport protocol want to unacknowledge an Information frame.  Table B.2: Frame Emission Events   Idle Sending Wait Ack  Send Split message in Information Split message in Information Split message in Information  Message frames with destination frames with destination frames with destination   address and frame number. address and frame number. address and frame number.   Store frames in se fuel dispenser nding Store frames in sending Store frames in sending  IFSF POSEPS ImplementationGuidelines - Revision - 20060510   fuel dispenser

we are committed to create the best workplace, encourage our staffs to put their own personalities into their jobs, and provide them a stage to show themselves.

    e Every Monday at 8am, Turkmenistan s schoolchildren line up to recite the oath of allegiance to the president, part of a youth-indoctrination programme that is progressively replacing the conventional curriculum. Its core is the two- volume Ruhnama, “The Book o fuel dispenser f the Spirit� a homespun collection of thoughts on Turkmen history and culture that pupils are required to spend hours studying. Visits to bookstores reveal shelves lined with nothing but the president s works. Meanwhile, mandatory education has been reduced from ten years to nine and most rural kindergartens have closed, as have all libraries outside the capital. Russian-language teaching has been largely phased out, music and ballet schools closed and almost all teachers of ethnic-minority origins sacked under rigorously enforced “Turkmenisation�policies that demand racial purity, traceable back three generations, for all workers in state institutions, including hospitals. Higher education is severely run down. The annual intake is now under 3,000, a tenth of the pre-independence figure, courses have been cut to two years and standards are so poor they are unacceptable abroad. Worse, the president has ordered that no foreign degrees will henceforth be recognised. Anyone with a qualification gained abroad is either being sacked or refused a job. One economist says that all but two of her high-school class of 30 have emigrated because they see no future at home. “You have students returning with degrees from the world s best universities—MBAs from Stanford, for instance—who can t get jobs,�she says. “We are the last educated generation,�sighs another professor. In rural areas, the problems are different. Cotton is the main crop, but the past three harvests have be fuel dispenser en catastrophic because of a requirement to sell at state-set prices so low that farmers are left with annual incomes of around $100. Unemployment is estimated at over 70%, exacerbated by public-sector layoffs, and by laws restricting job-seekers fuel dispenser